Gard Pro Pace

Power on

Press and hold the Power button for 3 seconds.

Blue light stays on for 3 seconds, then red and blue lights flash alternately. Voice prompt: power on / Bluetooth mode / pairing.

Power off

Press and hold the Power button for 5 seconds while powered on.

Red light flashes, then the headset powers off. Voice prompt: power off.

Connect to Bluetooth

After power-on, the headset enters pairing mode. Search for Gard Pro Pace on a phone, desktop computer, or laptop and select it to connect.

Red and blue lights flash alternately during pairing.

Successful pairing

The headset automatically searches for paired devices after power-on. For first-time use, connect manually from your device Bluetooth list.

Blue light flashes once every 5 seconds. Voice prompt: connected.

Bluetooth disconnected

Disconnect Bluetooth manually, or move out of Bluetooth range.

Red and blue lights flash alternately. Voice prompt: disconnected.

Long-distance reconnection

After returning to Bluetooth range, the headset reconnects.

Blue light flashes once every 5 seconds. Voice prompt: connected.

• Play / pause - when connected to Bluetooth music, click the Power button. The blue light flashes once every 5 seconds.
• Volume up - during playback, click the Volume + button. At maximum volume the headset gives a beep.
• Volume down - during playback, click the Volume - button.
• Previous song - during playback, double-click the Volume - button.
• Next song - during playback, double-click the Volume + button.

• Answer a call - for an incoming call, click the Power button.
• Reject a call - for an incoming call, press and hold the Volume + button for 2 seconds.
• End a call - during a call, click the Power button to hang up. The blue light flashes once every 5 seconds.
• Voice assistant - when connected by Bluetooth, press and hold the Volume - button for 2 seconds to enter voice assistant mode. Press and hold again for 2 seconds to exit.

When the headset is powered on, press the Volume + and Volume - buttons together to switch between French and English voice prompts. The switch is successful after the prompt tone is heard.

While powered on, press the Power button five times continuously. Pairing information is cleared and factory settings are restored. The headset returns to pairing mode.

Bluetooth is the default mode. Switching to TF card mode does not disconnect Bluetooth, and calls can still be answered.

• During Bluetooth playback, double-click the Power button to switch to TF card playback. The LED turns off and a TF card mode prompt is played.
• During TF card playback, double-click the Power button to switch back to Bluetooth playback.
• When TF card playback is paused, the blue light stays on.
• There is no voice broadcast when switching between TF and Bluetooth modes.
• When switching away from TF card playback and then back again, playback resumes from the current song and position.
• After shutdown and restart, the headset must be paired again if required.

To read or store TF card data, connect the headset to a computer with the data cable. The headset appears as a removable drive and the red and blue lights stay on. Disconnect the cable after reading or copying files; the headset then powers off.

• Use a charger that meets the recommended specifications: DC 5 V +/- 0.25 V, 100-500 mA.
• The headset cannot be powered on while charging. The red LED stays on during charging and turns blue when fully charged.
• The headset has a built-in non-removable rechargeable battery. Do not remove the battery; this may damage the headset.
• When the headset is not used for a long time, store it in a dry, ventilated place and recharge it every two months.
• A low-battery tone sounds approximately once per minute. If the battery is too low, the headset powers off automatically.
• When fully charged, unplug the charger from the power outlet and from the headset.
• Actual call time and standby time may vary depending on phone settings, usage, and environment.

⚠ Warning: use only approved chargers. Other chargers may violate approval requirements, create danger, or damage the electronic mainboard and battery.

• Wear the headset correctly, with the speakers positioned on the cheekbones in front of the ears. Do not place the speakers inside the ears.
• Listening at high volume for long periods may cause discomfort. Use a moderate volume to avoid prolonged high-volume listening.
• Using headphones can affect awareness of your surroundings regardless of volume. Pay extra attention when using the headset.
• Do not throw, sit on, crush, or immerse the headset in salt water. Keep it away from fire and high-voltage equipment.
• Not suitable for children under three years old. Contains small parts.

Do not dispose of this product with household waste. Take it to an appropriate local recycling point for electrical and electronic equipment. The battery is non-removable and should only be handled by an authorised service provider.

The company is not responsible for personal or property losses caused by violating these warnings.

Gard Pro - Health. Comfort. Open-ear listening.